Engine Data:
4-Cylinder Inline engine, camshaft located in the bottom of the engine block, the valves are operated by solid tappets, push rods and valve levers.
Installed in:
Cortina MK2 to MK5, Escort MK1 & MK2, Capri, Fiesta MK1
Comments:
In 1967 Ford changed the combustion chamber design, using a Heron type combustion chamber in the top of the piston rather than in the head.
Engine | Power | Year | Code | Comment |
OHV 1,3l | 49kW/67HP | 05/76-08/83 | J3E | HC-engine, KL13G |
OHV 1,6l | 62kW/84HP | 10/81-08/83 | L3E | HC-engine, KL16G |
Engine | Identifier | Year | Comment |
1,1l | 2733E-6085-A | 10/67-08/70 | |
1,1l | 2733E-6085-A | 08/70- | |
1,2l LC | 113E-6085-F | 09/62-09/66 | |
1,2l LC | 113E-6085-E | 09/62-09/66 | |
1,3l LC | 2730E-6085-B | 09/66-08/67 | |
1,3l LC | 2733E-6085-A | 10/67-08/70 | |
1,3l HC | 2730E-6085-A | 09/66-08/67 | |
1,3l HC | 2733E-6085-A | 08/67-08/70 | |
1,3l HC | 711M-6085-BA | 10/67-08/70 | "GT" |
1,3l | 711F-6085-BA | 08/70- | |
1,5l LC | 116E-6085-H | 09/62-08/67 | |
1,5l HC | 116E-6085-G | 04/63-08/67 | |
1,5l HC | 116E-6085-J | 04/63-08/67 | "GT" |
1,6l | 2737E-6085-C | 08/67-06/70 | |
1,6 | 2737E-6085-D | 08/67-06/70 | "GT" |
1,6l | 711M-6085-BA | 10/67-08/70 | |
1,6l LC | 711F-6085-BA | 08/70- | |
1,6l HC | 2737E-6085-F | 10/67-08/70 | "GT", Marine |
1,6l HC | 711F-6085-BA | 08/70- | |
1,6l HC | 711F-6085-CA | 08/70- | "GT" |
1,6l HC | 711F-6085-EA | 08/70- | "GT", Marine |
LC=Low Compression | |||
HC=High Compression |
Tighten the screws in the order shown in the illustration. Start with about half of the specified value and increase to the final value.
Tightening Torque | Nm |
Cylinder Head | 90-97 |
Intake Manifold | 21-25 |
Exhaus Manifold | 21-25 |
Valve Cover | 4-5 |
Spark Plugs | 30-40 |
Oil Drain Plug | 25-35 |
Cylinder 1 in the front in direction of driving
Firing Order 1-2-4-3
Ignition distributor rotates counter clockwise
Note: Spark plugs are located on the left side of the engine in the direction of driving
Engine Data:
4-cylinder Inline engine, camshaft located in the bottom of the engine block, the valves are operated by solid tappets, push rods and valve levers.
Installed in:
Fiesta MK1 to MK3, Escort MK3 to MK7
Comments:
This engine is a further development of the very succesful "A-Kent" engine. For the 1976 model year, the Kent engine was modified for transverse installation in the engine compartment of the new Ford Fiesta. The engine has been shortened by 30 mm and the number of main bearings has been reduced from five to three. The engines were now called "Valencia". With the appearance of the third series of the Ford Fiesta in 1989, the new "HCS" engine was introduced. This further development of the "Valencia" - which was named Valencia-HCS (high compression vortex; high compression, swirled) - had a different cylinder head with modified combustion and intake ports, the number of main bearings was again raised from three to five.
Engine | Power | Code | Year | Comment |
1,0l | 29kW/40HP | TKA | 05/76-08/83 | Valencia |
1,0l | 33kW/45HP | TLA | 05/76-08/83 | Valencia |
1,1l | 39kW/53HP | GLA | 05/76-08/83 | Valencia |